Wednesday, January 01, 2014

Repairing a HK42FZ007 Furnace Control Board

PLEASE DO NOT ATTEMPT THIS IF DO NOT KNOW WHAT YOU'RE DOING. Your furnace control system is a critical safety system. If you repair or install it incorrectly or damage the system, it can burn your home down or cause a gas leak with people inside, causing severe injury and/or death. I cannot emphasize this enough. Be careful, PLEASE! The following information is for informational purposes only.

For those people who would like to replace rather than repair their furnace board, I believe something like this should work: HK42FZ007.


The non-condensing forced air gas furnace in our home had been having intermittent trouble starting up. The furnace brand seems to be "Night and Day" and the model is Plus 80. The normal startup sequence is something like this:

  1. Inducer fan starts
  2. Hot surface igniter glows
  3. Gas turns on
  4. House blower turns on
The problem we had was the inducer fan in our furnace would cut in and out between step 1 and step 4. Most often, it would cut out right as the gas valve opened. This would correctly cause the inducer pressure switch to shutdown the furnace (the pressure switch is a safety mechanism). The problem here is that the inducer was cutting in and out; the inducer should not cut in and out if the thermostat is calling for heat.

After doing some initial debugging and internet research, I learned that our furnace uses a Carrier HK42FZ007 Furnace Control Board. This board is similar to a number of control boards such as HK42FZ004, HK42FZ008, HK42FZ009, and HK42FZ011. From my internet research, it seems that all these boards except the newest HK42FZ011 have a design flaw that causes one or two of the power resistor solder points to crack, leading to an intermittent connection. The symptoms are intermitted inducer behavior much like what our furnace was doing.

I pulled the board and took a peek. Here are some photos from this project:

The control board inside the furnace, showing wires connection points.


The control board inside the furnace, more wires.


The control board inside the furnace, even more wires.


To remove the board, there were two sheet metal screws holding the black case to the furnace. Make sure to record which wires go to which terminals before removing the board; I took detailed photos above.

The control board is out of the furnace.


Closeup of the control board box.


Closeup of the control board box another angle.


Back of the control board box.


To remove the board from the case, gently pry the back off. There are clips all around the edge, and if you are careful, you can remove the back without damaging the case. Inside, you will find the circuit board:

Circuit board front. Click for a larger version.


Circuit board back. Click for a larger version.


After some close inspection, I found cracks in the solder on R33 and R34, the large resistors in the board's cutout. Here's a closeup of the cracking. You can see the cracks on the two solder points on the left side of the image:

Cracked solder on the left two solder points.


To repair this problem, I used my soldering iron and reflowed the four solder points on those two resistors and added some more solder to the points also. Here's a photo of the repaired board. It's hard to see but the solder points are nice and solid now.

Repaired solder cracks.


I reinstalled the board and ran the control board's self-test. Everything seemed ok, so I fired up the furnace, and I have not heard the inducer hiccup for more than 6 hours now. I'm pretty certain the problem is fixed now.

I hope this is helpful for people out there facing a similar problem.

10 comments:

Unknown said...
This comment has been removed by a blog administrator.
BobNawroth said...

similar problem, same furnace, works sometimes, hear buzzing when it fails, I suspect bad IDR inducer relay K4.

Did your fix work?

Bob
bobbyfred@aol.com

Harris said...

This is very helpful, thanks! I have the same symptoms and replaced the inducer fan relay which did not improve things. Can you clarify where the cracks are? Are they where the resistors are supposed to be soldered onto the board? I couldn't see the cracks in your photos, and my board looks to be in better shape than yours. I guess I could try flowing more solder at the 4 points if that's what you mean. Thanks!

Unknown said...

Thank you so much. I am on my second c. board and the same thing kept happening. Your fix was right on the mark. The cracks are hard to see, but this is an easy fix if your handy w/ a soldering iron.

Alex said...

Bob, my fix did work. Its been running great since I wrote this blog post.

Harris, Yes the cracks are where the large resistors are soldered to the board. So I reflowed the 4 spots where the large resistors connect to the board.

Michael, I'm glad this blog post helped!

Unknown said...

I just found this -- Carrier Weathermaker 8000 with the HK42FZ011 module, same problem. The unit would cycle through the startup stages, stopping most often when the gas valve would open.

Only two heat cycles so far, but the fix seems to be working. I should note that the control board resistor solder points showed no obvious signs of cracking, but the amount of solder looked inadequate. I reflowed and added some additional solder.

Fingers crossed!

Alex said...

Great Scott!
I hope it works!

Unknown said...

If I want to just replace the board myself, what tools do I need? In particular, the multimeter sensitivity needed? Do I need " low impedance"??

Alex said...

Hi Walter,
To replace the board, I think you need just a screwdriver. A multimeter is not necessary, so I wouldn't worry about it. Just make sure the power to the furnace is off before you begin working on it.

Unknown said...

Wow, this fix just saved me a $99+ service call (during which they would probably try to sell me a whole new furnace) on a furnace that has worked flawlessly since I bought this 1957 house in 2002 but began to display intermittent interruption of the turn-on sequence at various stages this winter and generating various LED trouble codes. I wonder if it is original; if so, nothing you buy today is going to last 59 years. Knowing nothing, I threw a new thermostat at it - no help. I bypassed the blower compartment panel power switch - no help. Then I googled the control unit model number and bingo! I'm guessing that temperature cycling of those two large ceramic? resistors over time causes the problem. Anyway, even though no cracks were visible, I freshened up their solder joints and any others that looked cold. Everything is back to normal. Thank you SO much!